dstew29 78 Posted August 21, 2020 Share Posted August 21, 2020 1 minute ago, Felix said: Wow. Exactly the answer I wanted! Very interesting that you did ended up getting flatter hollow. Did you profiling your skates or only sharpening? I use the regular SS steps that come stock and yes, I had both sets profiled to a dual radius 20' / 32'. That seemed to be working good but I actually just got a new profile done using a prosharp - the "goalie SAM". We bunch of the local rinks have been shut down for the last few weeks due to a storm / power outage so I haven't been able to test them out yet. Will report back once I can get a few skates in. Quote Link to post Share on other sites
Teezle 66 Posted August 21, 2020 Share Posted August 21, 2020 7 minutes ago, dstew29 said: I can't speak to the custom asymmetrical grinds you were getting (#s 1 & 2), but for me, switching to True 1-piece made me go FLATTER than my usual preferred hollow (less energy loss all around vs riveted holders). I was getting 1/2" hollow on my old Graf w/ cowlings and went to 11/16" hollow on True 1-piece (trust me, I really dialed it in - tried 1/2", 5/8", 3/4", etc.). 11/16" just seemed to give me the preferred bite out of the box with the longest life between sharpens. Either way, the best general rule of thumb I heard with the 1-piece was go flatter by a 3/ to 4/16ths vs your usual hollow. Mine happened to be 3/16ths flatter. I think this is the case going from any traditional cowling skate to a modern no-cowling one. I was in Grafs - super comfortable skate, but their stock steel was very soft and I used to get my skates done at 3/8". Now I'm in a True 2-piece and after some experimentation, I use a 17/32" hollow on my skates. The increase in energy transfer to your blade is really noticeable! Quote Link to post Share on other sites
Puckstopper 261 Posted August 21, 2020 Share Posted August 21, 2020 I concur with going flatter. I used 3/8ths or 7/16ths on my old Bauer skates and dropped to 1/2" on my True's right off the jump. For profiling I mail my blades to NoIcing Sports in Delaware and have started using and liking their triple (15',20',28') radius. Previously I was using the double radius and I feel like the triple is absolutely worth the extra money for the extra mobility it offers. Quote Link to post Share on other sites
Felix 3 Posted August 24, 2020 Share Posted August 24, 2020 On 8/21/2020 at 9:15 PM, dstew29 said: I use the regular SS steps that come stock and yes, I had both sets profiled to a dual radius 20' / 32'. That seemed to be working good but I actually just got a new profile done using a prosharp - the "goalie SAM". We bunch of the local rinks have been shut down for the last few weeks due to a storm / power outage so I haven't been able to test them out yet. Will report back once I can get a few skates in. I've checked around all profiles and the Prosharp Goalie Sam seems be good for me. Do this profile prefer some specific rear/heel or front/toe as push position when pads are down on ice? On 8/21/2020 at 9:17 PM, Puckstopper said: I concur with going flatter. I used 3/8ths or 7/16ths on my old Bauer skates and dropped to 1/2" on my True's right off the jump. For profiling I mail my blades to NoIcing Sports in Delaware and have started using and liking their triple (15',20',28') radius. Previously I was using the double radius and I feel like the triple is absolutely worth the extra money for the extra mobility it offers. Whats different between yours 15',20',28' and the Goalie SAM 10',50,27'. I got information from Prosharp website. The SAM doesn't have any quatation mark but your profile has. Quote Link to post Share on other sites
Puckstopper 261 Posted August 24, 2020 Share Posted August 24, 2020 The Goalie SAM profile has a flat spot in the middle, which is what the 50 denotes. I tried Goalie SAM with my Tydan blades a couple years ago and didn't love it. It was only OK for me. I've tried a bunch of profiles and what I've liked from favorite to least favorite are: 15/20/28 - NoIcing 24/28 - NoIcing Goalie SAM - Tydan 17/28 - NoIcing 28' Stock radius 30' Peranis While I like being mobile while skating, I think the really short front section on the 17/28 and the Goalie SAM was TOO short for me to really grab an edge and move across while down. On the other hand, after trying a shorter radius up front I could never go back to stock or even flatter. Regardless, almost anything is better than that stock profile that comes on skates. If Goalie SAM was my only option I'd find a way to make it work! Quote Link to post Share on other sites
Chenner29 523 Posted August 24, 2020 Share Posted August 24, 2020 4 hours ago, Felix said: I've checked around all profiles and the Prosharp Goalie Sam seems be good for me. Do this profile prefer some specific rear/heel or front/toe as push position when pads are down on ice? Whats different between yours 15',20',28' and the Goalie SAM 10',50,27'. I got information from Prosharp website. The SAM doesn't have any quatation mark but your profile has. Goalie SAM is a 50mm flat spot in the center of the blade, not to be confused with a radius. Quote Link to post Share on other sites
DL42 34 Posted August 25, 2020 Share Posted August 25, 2020 its funny how everyone can use SAM profile no matter the weight height size skill level makes u wonder who is pushing this and why it is being pushed so hard. Extra revenue maybe with little expertise., hey skate shop we got a catch all template that goalie will like, we will sell it to you and u push it to the consumer for $50 or so, No experience needed , just throw the template on and they will like it. if they ask for any adjustment, just tell them this is it. Quote Link to post Share on other sites
ArdeFIN 110 Posted August 25, 2020 Share Posted August 25, 2020 This topic was interesting from the beginning. Would be super cool if someone had the possibility to test similar sets of blades with different edges in a subsequent test run to get the real difference. How does the shuffle go, benefits on kicking around in BF etc. This sharpening has the crucial balance in between stance/shuffle moves and BF. And it's about the playing style involved here too. Then we have the profile. How much does different profiles have to do with goaltending? I came from Bauer Vapor player skates with no profiling and goalie skates were easily chosen Vapor in the same size and fits well. In the first few ices as goalie I remember it was sooo difficult to just skate around because of the flat and long blade. I got used to it pretty quickly as being in front of the goal, skating is not that much of a matter. But I always wanted to have move curved profile. Then I got new blades with a lot steeper curve and how I love those. Oh yeah! But I didn't feel any change playing in goalie position, still have the (moderate) kicks and grip, can shuffle around, have equal balance in stance ie. Well I'm a lot more confident going out of crease to play that loose puck so a little change there. Quote Link to post Share on other sites
Felix 3 Posted August 25, 2020 Share Posted August 25, 2020 7 hours ago, Chenner29 said: Goalie SAM is a 50mm flat spot in the center of the blade, not to be confused with a radius. So basically the SAM has a little bit more stability because of the 50mm flat spot at center? If I'm remember correct I didn't like the stock profile on my old Bauer Elite because lack of movement at some positions, too way much stability. I couldn't push away from the post and get a C-grip with my skates toe to get back at same position/post. With a pair of player skate I could do this C-grip. Quote Link to post Share on other sites
Puckstopper 261 Posted August 25, 2020 Share Posted August 25, 2020 My understanding is that the idea behind the SAM is to give you a short front radius for mobility, the flat spot is for cross-crease movement and the 27' profile on the back is for a combination of mobility and strong pushes cross crease. Quote Link to post Share on other sites
dstew29 78 Posted August 25, 2020 Share Posted August 25, 2020 On 8/25/2020 at 7:54 AM, Puckstopper said: My understanding is that the idea behind the SAM is to give you a short front radius for mobility, the flat spot is for cross-crease movement and the 27' profile on the back is for a combination of mobility and strong pushes cross crease. On 8/24/2020 at 8:28 PM, DL42 said: its funny how everyone can use SAM profile no matter the weight height size skill level makes u wonder who is pushing this and why it is being pushed so hard. Extra revenue maybe with little expertise., hey skate shop we got a catch all template that goalie will like, we will sell it to you and u push it to the consumer for $50 or so, No experience needed , just throw the template on and they will like it. if they ask for any adjustment, just tell them this is it. I finally got back on the ice last night - competitive men's league scrimmage - so I have only one skate so far in the SAM profile. For reference again, I'm coming from profiled step steel for True 1 piece on No Icing 20/32 dual radius per above, which I skated on for about a year / year and half. First impressions are VERY good. First lap around the ice felt a little weird (which I fully expected would be the case) and mostly due to the flat section in the middle. I guess the best way to describe it was that I was getting the feeling of a dull edge/no bite at certain times due to the flatness of that section as my weight transferred around. Once I stretched out and got into the crease to move around a bit, I noticed a few big improvements right away: 1. Lateral pushes were way more efficient/effective. They felt easier due to that same gliding feeling but I never felt like I couldn't dig in to slow that down and never felt like the initial push lacked the edge/bite needed to get my momentum going. 2. Butterfly pushes and recoveries from butterfly were also extremely efficient. Never lost an edge or felt like I needed to angle my skate a certain way to get the most energy transfer. Just made moves as needed without even thinking about compensating for the new profile. It just worked with my game/technique. 3.One other thing that I was not happy with in my old profile was getting into that deep crouch / pre-shot set position that is obviously a major must have for all of us. My last profile also had a "Medium forward pitch" meaning, the steel was profiled / grinded to have a slight pitch forward from heel of the steel to the toe (I think most goalie boots and holders will also give you this slight pitch effect but this was recommended for the steel as well). The SAM profile I got was just standard/neutral or "no pitch". I felt like I couldn't easily glide into a deeper pre-shot crouch because my skate were digging in too much. Last night I felt like this was much easier for me shuffle and track with the shooter to my left or right a little if they were moving laterally before I crouched for the shot. Hopefully that helps some. And I agree with @ArdeFIN above, I wish there was a way to get universal feedback on profiles and hollows that everyone could find helpful to their own setups. Body types, style of play, equipment makes this hard to do but this is just my experience as I've tried stock, a dual profile and now the prosharp/SAM. I'm going to give it one more skate and if I get similar results to last night I'll be sending in my second set to Goalieparts.com to get the same treatment. Quote Link to post Share on other sites
Chenner29 523 Posted August 25, 2020 Share Posted August 25, 2020 8 hours ago, Felix said: So basically the SAM has a little bit more stability because of the 50mm flat spot at center? If I'm remember correct I didn't like the stock profile on my old Bauer Elite because lack of movement at some positions, too way much stability. I couldn't push away from the post and get a C-grip with my skates toe to get back at same position/post. With a pair of player skate I could do this C-grip. 50mm is tiny, 5cm or just under 2". 32 minutes ago, dstew29 said: First impressions are VERY good. First lap around the ice felt a little weird (which I fully expected would be the case) and mostly due to the flat section in the middle. I guess the best way to describe it was that I was getting the feeling of a dull edge/no bite at certain times due to the flatness of that section as my weight transferred around. Once I stretched out and got into the crease to move around a bit, I noticed a few big improvements right away: I wanna say what you are experiencing is better glide because (I'm guessing) you were in forward motion with weight on the 50mm flat section of the blade 7 minutes ago, dstew29 said: 3.One other thing that I was not happy with in my old profile was getting into that deep crouch / pre-shot set position that is obviously a major must have for all of us. My last profile also had a "Medium forward pitch" meaning, the steel was profiled / grinded to have a slight pitch forward from heel of the steel to the toe (I think most goalie boots and holders will also give you this slight pitch effect but this was recommended for the steel as well). The SAM profile I got was just standard/neutral or "no pitch". I felt like I couldn't easily glide into a deeper pre-shot crouch because my skate were digging in too much. Last night I felt like this was much easier for me shuffle and track with the shooter to my left or right a little if they were moving laterally before I crouched for the shot. Funny enough, I found a new local skate guy and gave him my steel to work on. I picked them up last night and it turns out we know a lot of the same folks. I've been getting free sharpenings from the local pro shop as I know most of the guys there. He showed me that the edges were misaligned on one of my runners (outside edge higher than inside). My other runner was completely flat in the back half. I've learned a little bit talking to skate guys over the years, but I learned a ton from this guy. My understanding breaks down as such: There are several different types of ProSharp templates - he had about a dozen stored on his machine. Templates resemble steel rulers with different radii cut out at the bottom (see below) Each template also has a center point, which typically aligns with the center line on your steel. This center point is generally the "highest" (when looking at steel from the bottom up) In order to achieve a forward pitch, the profile template is brought back towards the heel of the steel. The exact amount of this changes depending on how much pitch is requested. 1 Quote Link to post Share on other sites
dstew29 78 Posted August 25, 2020 Share Posted August 25, 2020 2 hours ago, Chenner29 said: 50mm is tiny, 5cm or just under 2". I wanna say what you are experiencing is better glide because (I'm guessing) you were in forward motion with weight on the 50mm flat section of the blade Funny enough, I found a new local skate guy and gave him my steel to work on. I picked them up last night and it turns out we know a lot of the same folks. I've been getting free sharpenings from the local pro shop as I know most of the guys there. He showed me that the edges were misaligned on one of my runners (outside edge higher than inside). My other runner was completely flat in the back half. I've learned a little bit talking to skate guys over the years, but I learned a ton from this guy. My understanding breaks down as such: There are several different types of ProSharp templates - he had about a dozen stored on his machine. Templates resemble steel rulers with different radii cut out at the bottom (see below) Each template also has a center point, which typically aligns with the center line on your steel. This center point is generally the "highest" (when looking at steel from the bottom up) In order to achieve a forward pitch, the profile template is brought back towards the heel of the steel. The exact amount of this changes depending on how much pitch is requested. Exactly right - well said. In my case, my previous profiler recommended shifting the "center point" a bit towards the heel of the runner which would rock your weight / center of gravity forward a bit. The further back they shift that point, the more aggressive your forward lean would be. For me so far, I much prefer a true center point on the profile - which is further enhanced on the SAM with the ~2" extended flat section. Quote Link to post Share on other sites
dstew29 78 Posted September 4, 2020 Share Posted September 4, 2020 On 8/25/2020 at 11:52 AM, dstew29 said: I'm going to give it one more skate and if I get similar results to last night I'll be sending in my second set to Goalieparts.com to get the same treatment. Got another fast scrimmage in with the SAM profile and I'm 100% sold versus anything else I've tried to date. For me at least, the other standard dual profiles I've tried just made it somewhat difficult to shuffle well and move laterally. I always felt like my edges were digging in too much and I never was able to get into a good groove where you almost feel like you're gliding and fluid with lateral shuffles, etc. The flat middle section is really the game changer in this department as it's just enough to get that lower friction movement in your shuffles. The prosharp offers a bunch of goalie profiles - and to be honest I sort of stumbled across this profile after reading a few times that pro goalies have used it or a version of the SAM. Others could be better for some of you but this one is spot on for what I've been looking for and couldn't be happier. Quote Link to post Share on other sites
Quadzilla32 50 Posted September 16, 2020 Share Posted September 16, 2020 hey guys, just got some new step runners and need to get them sharpened. I have read mixed things as far as whether or not I need to get cross grinding done on them for the first sharpening or just get my usual hollow? They are blacksteel if that adds anything. as far as I Understand cross grinding just is for prepping the runners for the first sharpen by removing any imperfections and making sure the profile is what you want. However, I thought the whole big deal about step is the quality of the steel so I’m guessing they are pretty spot on as far as profile and just need to be sharpened. Quote Link to post Share on other sites
dstew29 78 Posted September 16, 2020 Share Posted September 16, 2020 14 hours ago, Quadzilla32 said: hey guys, just got some new step runners and need to get them sharpened. I have read mixed things as far as whether or not I need to get cross grinding done on them for the first sharpening or just get my usual hollow? They are blacksteel if that adds anything. as far as I Understand cross grinding just is for prepping the runners for the first sharpen by removing any imperfections and making sure the profile is what you want. However, I thought the whole big deal about step is the quality of the steel so I’m guessing they are pretty spot on as far as profile and just need to be sharpened. Do you mean ‘blade matching’ right? Probably good to ask them to check just in case. I’m sure even Step blades could be slightly different from factory. If you’re happy with the relatively flat stock “profile” then yeah just hollow after they’re matched I would think... Quote Link to post Share on other sites
Quadzilla32 50 Posted September 16, 2020 Share Posted September 16, 2020 3 minutes ago, dstew29 said: Do you mean ‘blade matching’ right? Probably good to ask them to check just in case. I’m sure even Step blades could be slightly different from factory. If you’re happy with the relatively flat stock “profile” then yeah just hollow after they’re matched I would think... Thank you, I just want to be sure my LHS doesn’t mess them up, I do not have full confidence in some of the guys who do the sharpening. Quote Link to post Share on other sites
Felix 3 Posted October 2, 2020 Share Posted October 2, 2020 Goalie SAM is very good! I now can use my skate skills combined with stability. I also feel more grip at toe. Quote Link to post Share on other sites
Chenner29 523 Posted October 3, 2020 Share Posted October 3, 2020 On 9/16/2020 at 11:32 AM, Quadzilla32 said: Thank you, I just want to be sure my LHS doesn’t mess them up, I do not have full confidence in some of the guys who do the sharpening. Steel ain’t cheap. If you don’t trust your local guys, I would send them out to get done correctly. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.